Fixes you can do

How to reconnect solar monitoring after a new router or Wi-Fi change

The number one reason solar apps stop updating is a change to the home internet. Your panels are usually still working. Here is how to get the app back.

5 min readUpdated November 2026From the Energy Solution Providers service team

The short answer

The easiest fix is to give the new router the old Wi-Fi name and password: most solar devices reconnect on their own. If you cannot, plug the gateway in with an Ethernet cable or rerun the maker's Wi-Fi setup.

First, is it really just the monitoring?

Go to the inverter, or the gateway box on microinverter systems, on a sunny day. A normal green light means the system is producing and only the reporting has stopped. A red or amber light, or no lights at all, means something else is wrong too: start with the 5-minute check.

The easiest fix: reuse the old Wi-Fi name and password

Solar devices remember the Wi-Fi network name (SSID) and password they were set up with. If your new router uses exactly the same name and password, most of them reconnect on their own within an hour, with no setup at all.

  1. Find the old detailsThey are often on a sticker on the old router, or in your phone's saved networks. Capital letters matter.
  2. Set the new router to matchIn the new router's app or settings, change the network name and password to the old ones. Your internet provider's support line can do this with you.
  3. Wait, then check the appGive it an hour. If the app is still not updating, restart the gateway or inverter communication by switching the solar breaker off for a minute and back on.

The 2.4 GHz trap

Most solar inverters and gateways only connect on 2.4 GHz Wi-Fi. Many new routers and mesh systems combine 2.4 GHz and 5 GHz under one name, which some solar devices cannot join. If yours will not connect:

  • Look in the router settings for an option to split the bands, or to add a separate 2.4 GHz network for smart devices.
  • Make sure the signal reaches the inverter. Garages and outside walls are often at the edge of the Wi-Fi range. A mesh point or an outdoor-rated extender nearby can fix it.
  • Avoid passwords with unusual symbols, which some older solar devices handle badly.

The most reliable fix: a network cable

If the gateway or inverter has a network (Ethernet) port and a cable can reach it from the router, use it. It does not depend on Wi-Fi signal or passwords, and it survives the next router change too. Where running a cable is hard, a pair of powerline adapters (which send the network through your home's wiring) often works, although some solar equipment can interfere with them.

Reconnecting by brand

BrandHow it connectsHow to reconnect
EnphaseThe Envoy or IQ Gateway, by Wi-Fi, Ethernet or a cellular modemPress the gateway's AP mode button, then use the Enphase app's option to connect the gateway to Wi-Fi while you stand near it. Or plug in an Ethernet cable. See the gateway lights.
SolarEdgeThe inverter itself, by Wi-Fi, Ethernet, or a SolarEdge cellular or wireless kitNewer SetApp inverters are set up through SolarEdge's installer app, so homeowners often need help. Ethernet is the easy option. See the SolarEdge lights.
SMAThe inverter, by Wi-Fi or Ethernet, to Sunny PortalNewer Sunny Boys can join Wi-Fi through their own setup hotspot and a phone, and many support the WPS button on your router.
FroniusThe Datamanager card, by Wi-Fi or Ethernet, to Solar.webThe Datamanager can start its own setup hotspot. Connect a phone to it and follow the setup steps in the browser or the Fronius app.
APsystemsThe ECU box, by Wi-Fi or Ethernet, to the EMA appThe ECU has its own setup hotspot for the EMA Manager app, or use Ethernet.
TeslaThe Gateway, by Wi-Fi, Ethernet or its built-in cellularUse the Tesla app's Wi-Fi settings for the Gateway, or plug in Ethernet.

If it used a cellular connection

Many systems installed before about 2018 reported over 2G or 3G cellular networks. Those networks were shut down in Arizona by 2022, so these systems simply went quiet one day, with nothing changed at home. They need connecting to your home internet, or a newer modem from the maker.

Why it is worth fixing

Without monitoring, a fault can go unnoticed for months. We have seen systems that stopped producing a year before the owner found out from the bill. With the app working, you see a problem within a day.

Questions people ask

Do I lose my production data while it is offline?

Most gateways store several days to weeks of data and upload it once they reconnect. After a long gap, some of it may be lost, but the system keeps producing either way.

Can you reconnect it for me?

Yes. It is a short visit, and we check the system is actually producing while we are there.

This guide is general advice for Arizona homeowners. Your equipment's manual has the final word, and anything inside the inverter, on the roof or in the electrical panel is a job for a licensed contractor.

Accredited, award-winning and Arizona licensed

AriSEIA member — Arizona Solar Energy Industries AssociationHomeAdvisor Top RatedHomeAdvisor Elite Service awardBetter Business Bureau accredited business, A+ ratingSolarReviews — read our customer reviewsAngi Super Service Award 2023Angi Super Service Award 2022
Call us Text Get a free quote

Type at least two letters.